NEWTON
WATERPROOFING FLOORING MEMBRANES
Newton 503 - M5
Newton 503 is a 3mm HDPE high quality cavity drain
waterproofing and damp-proofing membrane suitable for use internally
above or below the ground to retaining walls, vaulted soffits and
floors. When Newton 503 is used as part of Newton System 500 it is
essential that a Newton pumping system or a safe form of drainage is
specified.
Click here to view the full product details
for Newton 503 on www.newton-membranes.co.uk
Newton 508 - M1 & M2
In the majority of Newton System 500 installations, 8mm stud Newton 508
is the professional waterproofing contractors wall membrane of choice.
Newton 508 (HDPE) is also suitable to be used as a flooring membrane
within Newton System 500 and often the designer or installer will use
the same membrane for both walls and floor.
Where space is at a premium, Newton 508 can be substituted with the 3mm
Newton 503. All Newton wall membranes are fixed to the wall with the
Newton MultiPlug or Newton Nu-seal Plug.
Click here to view the full product details
for Newton 508 on www.newton-membranes.co.uk
Newton 520 - M4 & M13
Newton 520 with its 20mm stud profile is usually specified
when the slab or raft is of questionable quality and the concern is that
water could pass through the concrete itself and not just at the cold
joints in the structure. The recommended finish above Newton 520 is a
65mm sand / cement screed. For other finishing options or being
considered, please contact John Newton. When Newton 520 is used as part
of Newton System 500 it is essential that a Newton pumping system or a
safe form of drainage is specified.
Click here to view the full product details
for Newton 520 on www.newton-membranes.co.uk
Newton 501 Slimline - M6
Newton 501 Slimline has a unique profile that allows the movement of
vapour below the membrane. 501 Slimline is particularly useful when
protecting sensitive flooring from dampness in new concrete as it can be
laid as soon as the concrete floor is able to be walked upon. Suitable
finishes are screed and floating timber flooring. Newton 501 Slimline
can be specified by a qualified waterproofing surveyor to be used as the
flooring membrane within System 500. Newton 501 Slimline has a very high
loading capability of over 1000 kN/m2 and is often specified within
System 500 as a loading DPM within internal load bearing walls.
Click here to view the full product details
for Newton 501 Slimline on www.newton-membranes.co.uk
Newton 503 Mesh - M11 & M12
Newton 503 Mesh is ideally suited as a floating floor membrane when a
bonded key is required for tiling, natural stone or paving, providing
both a waterproofing membrane and a vapour pressure equalisation layer.
Newton 503 provides separation between the floor and the floor covering,
bridging stress cracks and other slight defects in the substrate so that
they are not transferred to the floor covering above. With the flat 3mm
studs filled with the tiling adhesive, the floor loading is transferred
through the studs to an area of approximately 60% of the floor area
above.
Click here to view the full product details
for Newton 503 Mesh on www.newton-membranes.co.uk
Newton 503 Floor Tile - M7
Newton 503 Floor Tile the sister product to Newton 503 Mesh, has an
additional anchoring fleece to the studded side for bonding the membrane
to the substrate. When adhered with Newton Floor Tile Adhesive, Newton
503 Floor Tile provides a fully bonded water and vapour proof membrane
with superb soundproofing and cushioning properties. Suitable finishes
are tile, stone and paved flooring. Newton 503 Floor Tile can be
specified by a qualified waterproofing surveyor to be used as the
flooring membrane within System 500.
Click here to view the full product details
for Newton 503 Floor Tile on www.newton-membranes.co.uk
Case
studies on numerous successful projects and full product details are
available at
www.newton-membranes.co.uk
Download Newton System 500 Brochure
